Siemens SICAM P 7KG7750 Скачать руководство пользователя страница 103

Страница: 103 / 142

5.8 Additionals

103

Power Meter SICAM P 7KG7750/55, Manual
E50417-B1076-C340-A6, Edition 09.2013

parameterization menu from the buttons on the device. The relevant menu is only enabled if you
enter the correct password.

Code 1

•

without

: no security

•

with

: device code 1 is only active if code 2 is activated as well.

Functions secured: screen parameterization, reset energy min / max values and changing
device language.

Code 2

•

without

: no security (code 1 also deactivated)

•

with

: code is activated

Saved functions: basic parameters (connection / transformers, outputs, interface, change
code, adjustment, other settings)

Notes:

•

A password always consists of a 6-digit number.

•

If you forget your password, you can activate the machine either using a master password
(available from the hotline, see Foreword) or using the SICAM P parameterization software.

•

Device code 1 is only active if code 2 is activated as well.

•

If code 1 and 2 are activated, the code 2 password can also be used to unlock all the func-
tions secured using code 1.

•

If the secured parameter settings are called up in SICAM P, a window appears asking you to
enter a password.

•

If a secured parameter is unlocked by entering a password on the device, a new password
prompt appears after a wait of 1 minute in level 1.

Note

The software does not require a password.

Содержание SICAM P 7KG7750















































































































































Результаты поиска

Содержание SICAM P 7KG7750

Отзывы:

Siemens SICAM P 7KG7750, Руководство пользователя, Страница: 103 / 142

Результаты поиска

Содержание SICAM P 7KG7750

Отзывы: