Siemens SICAM P 7KG7750 Скачать руководство пользователя страница 111 | Manualshive

Страница: 111 / 142

Siemens SICAM P 7KG7750 Скачать руководство пользователя страница 111

5

5.9 Memory Management

111

Power Meter SICAM P 7KG7750/55, Manual
E50417-B1076-C340-A6, Edition 09.2013

5. Also, you must indicate the

Averaging interval

(5 s, 10 s, 15 s, 30 s, 1 min, 5 min, 10 min,

15 min, 30 min, 60 min) and the

Storage interval

(5 s, 10 s, 15 s, 30 s, 1 min, 5 min, 10 min,

15 min, 30 min, 60 min). These parameters set the number of measured values to be used
for mean value calculation and the interval for saving the values.

5.9.3

Power Values

In this dialog window you can specify the settings for power recording.

Proceed as follows:

1. Select up to eight

Measured values

and

Test points

.

2. Select a

Date

or one of the six

Limit value groups

as

Start selector

for the power recording.

It is possible to combine Date and Limit value group as start selectors. The first of the two
criteria fulfilled, will launch the recording.

3. When entering a date as

Start selector

, you must indicate a year between 2000 and 2060.

Note

If you have entered a past start date, SICAM P will initiate mean value recording immediately
after the setting. Manual start is not activated by configuration but can be initiated at any time.

Note

If the device provides additional analog inputs (optional), you can record external measurement
signals.

«
...
109
110
111
112
113
...
»

Содержание SICAM P 7KG7750















































































































































Отзывы:

Нет отзывов