manualshive.com logo in svg

Siemens SICAM P 7KG7750, Руководство пользователя, Страница: 138 / 142

Поделиться
Скачать
Siemens SICAM P 7KG7750 Скачать руководство пользователя страница 138

8 

8.1 SICAM P 7KG7750

138

Power Meter SICAM P 7KG7750/55, Manual

E50417-B1076-C340-A6, Edition 09.2013

8.1.1.4

Environmental Conditions

Temperature data
IEC/EN 60068

Operating temperature

Devices with display: the legibility of the display is 
impaired at temperatures < 0 °C (+32 °F).

-25 °C to +55 °C
-13 °F to +131 °F

Temperature during transport

-25 °C to +70 °C
-13 °F to +158 °F

Temperature during storage

-25 °C to +70 °C
-13 °F to +158 °F

Maximum temperature gradient

20 K/h

Air humidity data

Mean relative humidity per year

≤

 75 %

Maximum relative humidity

80 % for temperatures up to 
31 °C (87.8 °F);
decrease linearly to 50 % at 
40 °C (104 °F)

Condensation during operation

Not permitted

Condensation during transport and storage

Permitted

Altitude

Max. altitude above sea level

2000 m

Pollution degree

2

Содержание SICAM P 7KG7750















































































































































Отзывы:

Нет отзывов