manualshive.com logo in svg

Siemens SICAM P 7KG7750, Руководство пользователя, Страница: 34 / 142

Поделиться
Скачать
Siemens SICAM P 7KG7750 Скачать руководство пользователя страница 34

2 

2.1 Screen Display

34

Power Meter SICAM P 7KG7750/55, Manual

E50417-B1076-C340-A6, Edition 09.2013

2.1

Screen Display

Once the SICAM P has been connected and configured for its measuring task, the measured 
quantities you have defined are displayed in screens.

•

Specific screens can be selected via the two front arrow buttons 

. 

•

Press an arrow button once to display the next or previous screen.

•

Hold an arrow button down to scroll through the screens automatically

•

If desired, automatic scrolling can be programmed for normal display. When scrolling, the 
screens are arranged in a loop format (i.e., the first screen follows the last in one direction, 
whereas the last screen follows the first in the opposite direction, etc.).

2.2

Screen Content

The simple and individual screen design enables you to read the information relevant to your 
measuring tasks at a glance. The number of screens (max. 20), the screen types and their con-
tents can be parameterized as required. 

2.2.1

Screen Types

The following screen types are available:

•

three measured values - digital

•

six measured values - digital

•

U, I, cos 

φ

•

three min-max values

UL1

231.35

V

UL2

230.87

V

UL3

229.46

V

2/10

AP

<>  Bd/Prm

Min-Max       12:30

   230.11

UL1

   233.53   V
   228.59

UL2     231.47   V

   227.33

UL3     233.48   V

2/10

AP

<>  Bd/Prm

UL1

231.35

V

UL2

230.87

V

UL3

229.46

V

2/10

AP

<>  Bd/Prm

Содержание SICAM P 7KG7750















































































































































Отзывы:

Нет отзывов