manualshive.com logo in svg

Siemens SICAM P 7KG7750, Руководство пользователя, Страница: 30 / 142

Поделиться
Скачать
Siemens SICAM P 7KG7750 Скачать руководство пользователя страница 30

1 

1.6 Interface and Terminals

30

Power Meter SICAM P 7KG7750/55, Manual

E50417-B1076-C340-A6, Edition 09.2013

1.6.5

Mounting

To mount the device proceed as follows:

•

Swing the mounting element (provided with the device) over the rear cone.

•

Move the mounting element to the position. Use a screw driver (0.6 x 4.5) mm to fix the moun-
ting elements until the slipping clutch takes effect.

Fig. 1-9 

Mounting

WARNING

Warning about dangerous voltages when operating an electrical device.

Nonobservance of the safety instructions means that death, severe
injuries or considerable material damages can occur.

•

The SICAM P is a build-in device and must therefore be in-stalled on a switchboard or in a 
control cabinet. After installation, it is important that all terminals are properly covered to pre-
vent accidental contact with energized parts.

Notes

•

The device location should be largely free from vibrations.

•

The device must be operated within allowable ambient temperature limits. Operating the 
device outside of the operating temperature range can lead to measurement errors and 
device failure.

•

Steps should be taken to minimize exposure of the device to direct sun light and large tem-
perature variations. 

•

Minimum thickness of the mounting plate: 1 mm; steel.

•

Steps must be taken to prevent condensation on or within the device during operation.

•

To prevent accidental contact with energized parts the above described mounting must be 
taken care-fully and correctly. 

Содержание SICAM P 7KG7750















































































































































Отзывы:

Нет отзывов