manualshive.com logo in svg

Siemens SICAM P 7KG7750, Руководство пользователя, Страница: 32 / 142

Поделиться
Скачать
Siemens SICAM P 7KG7750 Скачать руководство пользователя страница 32

1 

1.6 Interface and Terminals

32

Power Meter SICAM P 7KG7750/55, Manual

E50417-B1076-C340-A6, Edition 09.2013

1.6.7

Electrical Connection

WARNING

Warning about dangerous voltages when operating an electrical device.

Nonobservance of the safety instructions means that death, severe
injuries or considerable material damages can occur.

•

Only qualified people shall work on and around this device. They must be thoroughly familiar 
with all warnings and safety notices in this instruction manual as well as with the applicable 
safety steps, safety regulations, and precautionary measures.

  

•

The following work is partly carried out at existence endangering voltages.

Note

•

During electrical installation, all rules and regulations for power systems must be observed.

•

For measurements in three-phase networks without neutral in V-connection and a nominal 
voltage of U

LL

 

= 690 V, the voltage must be transformed to U

LL

 

≤  

400 V. The measuring 

range to be parameterized is then also U

LL

 

= 690 V. 

•

Short-circuit the current transformer secondary circuits before current connections to the 
device are opened.

•

The protective ground terminal of the device must be connected to the protective ground of 
the panel or cubicle.

•

For connection of an auxiliary DC voltage, the correct polarity must be used.

•

All of the terminals should be checked to verify proper connections.

•

The polarities and phasing of all instrument transformers should be checked.

•

Use screw-type terminals for 2.5 mm

2

.

•

In IT networks, the SICAM P cannot be connected directly because the voltage is measured 
against the PE conductor connection and the input impedance of the device causes a leak-
age current against earth. The leakage current can cause tripping of the leakage protective 
system in IT networks. Please make sure that the maximum permissible input voltage of the 
SICAM P against earth U

L-PE

 

= 480 V is not exceeded (e.g., due to an earth fault of one 

phase). Voltage transformers must be used in IT networks. 

•

Before initially energizing the device with supply voltage, it shall be situated in the operating 
area for at least two hours to ensure temperature equalization and to avoid humidity and con-
densation problems.

Содержание SICAM P 7KG7750















































































































































Отзывы:

Нет отзывов