Siemens SENTRON PAC3200T Скачать руководство пользователя страница 84

Страница: 84 / 136

Technical data

8.1 Technical data

Equipment Manual, 09/2022, L1V30415168B-03

Degree of protection and protection class

Protection class

Safety class II

Degree of protection according to IEC 60529

Front area

IP40

Termination area

IP20

If higher degree of protection requirements are placed on the application engineering, the

customer must take suitable measures. This includes installation in a protective enclosure

with degree of protection IP51 or higher.

Environmental conditions

Operation is only permissible inside an enclosed dry room.

Environmental conditions

Temperature range

Ambient temperature during operating

phase

-25 °C … +55 °C /

-40 °C ... +70 °C

(depending on HW, see device)

Ambient temperature during transport

and storage

-40 °C ... +70 °C

Relative humidity

< 75 % RH

Installation altitude above sea level

max. 2000 m

Device mounting position

Any

Degree of pollution

Environmental tests

EN 60068-2-6

EN 60068-2-27

EN 60068-3-3

Electromagnetic environment

interference emission

EN 61326-1

EN 61000-3-2 (harmonic currents)

EN 61000-3-3 (voltage variations and flicker)

Limit values complied with for emitted

interference

Class B, used in the household sector

Interference immunity

EN 61326-1

(use in an industrial environment)

Standards considered for immunity

EN 61000-4-2 (electrostatic discharge)

EN 61000-4-3 (electromagnetic RF fields)

EN 61000-4-4 (rapid transients - burst)

EN 61000-4-5 (surge voltages - surge)

EN 61000-4-6 (conducted RF fields)

EN 61000-4-8 (magnetic fields)

EN 61000-4-11 (voltage dips)

Содержание SENTRON PAC3200T









































































































































Результаты поиска

Содержание SENTRON PAC3200T

Отзывы:

Siemens SENTRON PAC3200T, Руководство по эксплуатации продукта, Страница: 84 / 136

Результаты поиска

Содержание SENTRON PAC3200T

Отзывы: