Siemens SENTRON PAC3200T Скачать руководство пользователя страница 57

Страница: 57 / 136

Commissioning

6.3 Parameterizing the device

Equipment Manual, 09/2022, L1V30415168B-03

6.3.1

Setting basic parameters with powerconfig

6.3.1.1

Establish connection to the device (via Ethernet)

In order to establish a connection to the PAC3200T via Ethernet, proceed as follows:
1.

Connect the device to the PC or network via the Ethernet interface.

Make sure that the PAC3200T and the configuration computer are located in the same

subnet.

Open the powerconfig configuration software.

On the toolbar, click on the "Search for accessible devices" key or alternatively press the

"F11" key.

The "Search for accessible devices" window opens.

In the "Search for Accessible Devices" window, click on the "Ethernet" tab.

The "Ethernet" view is displayed.

Select the Ethernet interface from the selection list.

Click on the "Start search" button.

Select the desired device.

If necessary, adapt the communication settings.

To do this, switch the edit mode to "Unlocked". Carry out the required settings in the menu

options "IP address", "Network mask", "Gateway" etc.

Click on the button "Load changes to configuration parameters into device(s)".

10.

Click the "Create devices" button.

The selected device is added.

11.

In menu item "Views", select the sub-menu "Parameters".

The "Parameters" window opens.

12.

In the "Parameters" window, click on the "Load to PC" button.

The configuration is loaded into the PC from the device.

Содержание SENTRON PAC3200T









































































































































Результаты поиска

Содержание SENTRON PAC3200T

Отзывы:

Siemens SENTRON PAC3200T, Руководство по эксплуатации продукта, Страница: 57 / 136

Результаты поиска

Содержание SENTRON PAC3200T

Отзывы: