Siemens SENTRON PAC3200T Скачать руководство пользователя страница 64

Страница: 64 / 136

Commissioning

6.3 Parameterizing the device

Equipment Manual, 09/2022, L1V30415168B-03

"Hardware write-protection" parameter

The hardware write protection prevents write access to the device.
In order to gain write access, the hardware write protection must be deactivated directly on

the device.

Selection

Range

Factory

setting

Hardware write

protection

•

OFF:

Hardware write protection is deactivated.

OFF

•

ON:

Hardware write protection is activated.

Activation or deactivation of the hardware write protection must be confirmed on the device.

The Power LED on the device flashes for 15 minutes. By pressing the SW button on the device

during this flashing period, the protection function is activated or deactivated.

"Device access control (IP filter)" parameter

The IP filter is a configurable access protection. If activated, Modbus TCP write commands are

only accepted if the remote station is located in the same subnet.

Selection

Range

Factory

setting

Device access control

•

OFF:

Protection is deactivated.

OFF

•

ON:

Protection is activated.

TCP/IP settings

parameter

Ports are communication channels which make it possible to access a Modbus-capable device

via a network.
Standard IP ports like port 502 are often tested by port scanners. If an open port is discovered

by an attacker, the device can be attacked via this port. The PAC3200T allows the Modbus

TCP ports to be configured manually. Switching from standard port 502 to a user-defined port

makes it more difficult to scan for open ports. The Modbus TCP communication port 502 is

used as the default setting.

Содержание SENTRON PAC3200T









































































































































Результаты поиска

Содержание SENTRON PAC3200T

Отзывы:

Siemens SENTRON PAC3200T, Руководство по эксплуатации продукта, Страница: 64 / 136

Результаты поиска

Содержание SENTRON PAC3200T

Отзывы: