Siemens SENTRON PAC3200T Скачать руководство пользователя страница 27

Страница: 27 / 136

Description

2.6 Digital inputs and outputs

Equipment Manual, 09/2022, L1V30415168B-03

2.6.2

Digital output

The following functions can be assigned to the digital output:

•

Not used:

The digital output is deactivated.

•

Device ready for operation:

With the device ready for operation the digital output is ON.

•

Remote control:

The digital output is remotely controlled.

•

Direction of rotation

The digital output is switched on by a counter-clockwise rotating electrical field and

remains active while the direction of rotation of the field remains unchanged.

•

Limit violation:

The digital output is switched on by a limit violation and remains active while the limit

violation prevails.

•

Energy pulse

The digital output outputs the parameterized number of pulses per energy unit (e.g. kWh).

The specified energy counter is evaluated here.

Figure 2-2

Block diagram: Digital outputs

Содержание SENTRON PAC3200T









































































































































Результаты поиска

Содержание SENTRON PAC3200T

Отзывы:

Siemens SENTRON PAC3200T, Руководство по эксплуатации продукта, Страница: 27 / 136

Результаты поиска

Содержание SENTRON PAC3200T

Отзывы: