Siemens SENTRON PAC3200T Скачать руководство пользователя страница 81

Страница: 81 / 136

Technical data

8.1 Technical data

Equipment Manual, 09/2022, L1V30415168B-03

Measuring accuracy

Applicable standards:
•

IEC 61557-12

•

IEC 62053-22

•

IEC 62053-23

Measured variable

Accuracy class

Voltage

0.5 (IEC 61557-12)

Current

0.5 (IEC 61557-12)

Neutral conductor current (calculated)

1 (IEC 61557-12)

Total apparent power

0.5 (IEC 61557-12)

Total active power

0.5 (IEC 61557-12)

Total apparent power

0.5 (IEC 61557-12)

Total reactive power

2 (IEC 61557-12)

Total power factor

0.5 (IEC 61557-12)

Line frequency

0.05 (IEC 61557-12)

Total active energy

0.5 (IEC 61557-12)

Total reactive energy

2 (IEC 61557-12)

Total active energy

0.5 (IEC 62053-22)

Total reactive energy

2 (IEC 62053-22)

When measuring on external current transformers or voltage transformers, the accuracy of

the measurement depends on the quality of the transformer.

Power supply

Design of the power supply

Wide range AC / DC power supply

Work area

110 V - 250 V ±10%

Power consumption

5 VA

Overvoltage category

OVC

Digital Input

Number

Type

Passive

Maximum switching voltage

30 V

Input current

"1" signal detection

2.5 … 10 mA

"0" signal detection

≤0.5

Содержание SENTRON PAC3200T









































































































































Результаты поиска

Содержание SENTRON PAC3200T

Отзывы:

Siemens SENTRON PAC3200T, Руководство по эксплуатации продукта, Страница: 81 / 136

Результаты поиска

Содержание SENTRON PAC3200T

Отзывы: