Siemens SENTRON PAC3200T Скачать руководство пользователя страница 75

Страница: 75 / 136

Equipment Manual, 09/2022, L1V30415168B-03

Service and maintenance

7.1

Cleaning

Clean the device as required. Use a dry cloth for this.

NOTICE
Damage may result from use of detergents.

Detergents can damage the device. Do not use detergents.

DANGER

Hazardous voltage.

Will cause death, serious personal injury, or equipment damage.

Turn off and lock out all power supplying this equipment before working on this device.

7.2

Calibration

The device has been calibrated by the manufacturer before shipping. Recalibration is not

required provided the environmental conditions are maintained.

7.3

Firmware updates

The PAC3200T supports firmware updates.
When updating, always use the latest version of the powerconfig configuration software. For

update instructions, please see the related documentation and the online help for the

configuration software.
For an update, the write protection and password protection must be temporarily disabled.

Please ensure that the environment is safe.
The last devices settings made remain unchanged.
The current firmware can be downloaded via the Siemens homepage (

https://sie.ag/3Q8I2tn

Содержание SENTRON PAC3200T









































































































































Результаты поиска

Содержание SENTRON PAC3200T

Отзывы:

Siemens SENTRON PAC3200T, Руководство по эксплуатации продукта, Страница: 75 / 136

Результаты поиска

Содержание SENTRON PAC3200T

Отзывы: