Siemens SENTRON PAC3200T Скачать руководство пользователя страница 76

Страница: 76 / 136

Service and maintenance

7.4 Troubleshooting guide

Equipment Manual, 09/2022, L1V30415168B-03

7.4

Troubleshooting guide

Remedies for the resolution of faults

Fault

Remedies

Device is not working

•

Check power supply

•

Check supply voltage

•

Check fuse

Voltage or current measured values are not

displayed

•

Check fuse

•

Check configuration

(see Parameterizing the device (Page 54))

Voltage values are not plausible

•

Check the voltage transformer setting and correct if necessary

Current values are not plausible

•

Check the current transformer setting and correct if necessary

No communication

•

Check the communication settings

(incorrect IP address, incorrect subnet or gateway?)

•

Check firewall, if present

(possibly preventing communication to the Modbus ports)

"Overload" LED flashes red

•

Voltage or current input overridden. Check parameters of the

measuring voltage

•

Check installed current transformer

(dimensioning too small)

Power values are incorrect, although voltage

and current are correctly applied

•

Check voltages and currents of the phases

(not properly connected to one another)

•

Check the current transformer

(for incorrect polarity)

If the device fault cannot be remedied by the measures given above, the device is probably

defective.
More help can be found on the Internet. (

https://www.siemens.de/lowvoltage/technical-

assistance

)

If the device is defective, please proceed as follows:
•

See chapter Warranty (Page 75) if the device has become defective within the warranty

period.

•

If the device has become defective outside the warranty period, the device must be

disposed of in accordance with local disposal regulations.

See also

Parameterizing the device (Page 54)

Содержание SENTRON PAC3200T









































































































































Результаты поиска

Содержание SENTRON PAC3200T

Отзывы:

Siemens SENTRON PAC3200T, Руководство по эксплуатации продукта, Страница: 76 / 136

Результаты поиска

Содержание SENTRON PAC3200T

Отзывы: