Siemens SENTRON PAC3200T Скачать руководство пользователя страница 16

Страница: 16 / 136

Description

2.1 Features

Equipment Manual, 09/2022, L1V30415168B-03

Interfaces

•

Ethernet interface

•

Digital Input

•

Digital output

A description of the inputs and outputs can be found in section "Digital inputs and outputs

(Page 23)".

Security

•

Hardware write protection

•

Access protection IP filter

•

Modbus TCP port, configurable

•

HTTP port, configurable

•

Dynamic host configuration protocol (DHCP) included

•

Simple network time protocol (SNTP) included

•

Attachment of lead seals possible

A description of how to protect the device can be found in section "Extended (further

parameters) (Page 59)".

Note
Activate hardware write protection

When connecting the measuring device to a network, it is recommended that the hardware

write protection is activated.

Tariffs

PAC3200T supports 2 tariffs for the integrated energy counters (high tariff and low tariff).

Control of tariff switching

Switching between off-peak and on-peak can be controlled via the digital input or the

communication interfaces.
Time-related switching is only possible using a higher-level system.

Tariff switching after synchronization

When synchronizing the average power demand values via the communication interfaces or

the digital input, the tariff change will only become effective after expiry of the period. The

power demand is always synchronized by the time. Tariff switching is only done after expiry

of the current period.
The synchronization frame contains the length of the demand period in minutes. The

synchronization command is ignored if the period length sent to the device with the

synchronization frame is different to the length parameterized in the device.

Содержание SENTRON PAC3200T









































































































































Результаты поиска

Содержание SENTRON PAC3200T

Отзывы:

Siemens SENTRON PAC3200T, Руководство по эксплуатации продукта, Страница: 16 / 136

Результаты поиска

Содержание SENTRON PAC3200T

Отзывы: