Siemens SENTRON PAC3200T Скачать руководство пользователя страница 73

Страница: 73 / 136

Commissioning

6.3 Parameterizing the device

Equipment Manual, 09/2022, L1V30415168B-03

"Power demand" parameter

The "power demand" parameter permits the following device settings:

Selection

Range

Factory setting

Time period

The time period records the duration of the period in minutes.

Range: 1 min to 60 min

Synchronization

mode

Setting of the synchronization mode:

•

No synchronization:

Switches "Synchronization via Bus" off. Synchronization only takes place after

time set internally in device.

•

Synchronization via Bus:

Activates "Synchronization via Bus". Deactivates "Synchronization via Digital

Input" or "Synchronization via internal clock".

•

Synchronization via Digital Input:

Activates "Synchronization via Digital Input". Deactivates "Synchronization via

Bus" or "Synchronization via internal clock".

•

Synchronization via internal clock:

Activates "Synchronization via internal clock". Deactivates "Synchronization via

Bus" or "Synchronization via Digital Input".

Содержание SENTRON PAC3200T









































































































































Результаты поиска

Содержание SENTRON PAC3200T

Отзывы:

Siemens SENTRON PAC3200T, Руководство по эксплуатации продукта, Страница: 73 / 136

Результаты поиска

Содержание SENTRON PAC3200T

Отзывы: