Siemens SENTRON PAC3200T Скачать руководство пользователя страница 68

Страница: 68 / 136

Commissioning

6.3 Parameterizing the device

Equipment Manual, 09/2022, L1V30415168B-03

Example:

LIM0, LIM1, LIM3 and LIM5 are to be linked to one another with the following logic:

Selection of the operators:

op0: AND (Λ)

op1: AND (Λ)

op2: ----

op3: AND (Λ)

op4: ----
op5: OR (V)

Formula:

(((((AND LIM0 AND LIM1) ---- LIM2) AND LIM3) ---- LIM4) OR LIM5) = RLO

Simplified representation: ((LIM0

LIM1)

LIM3) V LIM5 = RLO

"Universal Counter" parameter

The "Universal Counter" parameter is a configurable counter. It shows the source from which

status changes or limit violations are counted:
•

"Digital input" - Status changes at the digital input are counted (rising edge only).

•

"Digital output" - Status changes at the digital output are counted (rising edge only).

•

"Result Logic Array" - A violation of this limit value is counted.

•

"Limit 0" to "Limit 5" - A violation of this limit value is counted.

Содержание SENTRON PAC3200T









































































































































Результаты поиска

Содержание SENTRON PAC3200T

Отзывы:

Siemens SENTRON PAC3200T, Руководство по эксплуатации продукта, Страница: 68 / 136

Результаты поиска

Содержание SENTRON PAC3200T

Отзывы: