Siemens SENTRON PAC3200T Скачать руководство пользователя страница 34

Страница: 34 / 136

Connection

4.1 Safety notes

Equipment Manual, 09/2022, L1V30415168B-03

CAUTION

Voltage input conductors may be damaged.

The fuses in the voltage measuring inputs are only used for cable protection. Selection of

the fuse depends on the supply cable dimensioning. All commercially available fuses and

automatic circuit breakers up to 16 A (C) or 20 A (B) can be used. Observe the applicable

regulations when selecting the fuse.
We recommend 5SY miniature circuit breakers, 3RV motor starter protectors, or 5SB/3NA

fuses, depending on the cable requirements and connection conditions.
Voltage input conductors must be protected.

NOTICE
The wrong system connection can damage the device.

Failure to heed this warning can result in damage to the device and the system. The

minimum and maximum limits given in the technical data and on the rating plate must not

be exceeded even during startup or testing of the device.

Note
Grounding of current transformers optional.

Always connect the transformers and ground them on the secondary side in accordance with

the applicable regulations. Grounding of the current transformers on the secondary side is

not necessary for use in low-voltage switchboards for performing measuring tasks.

NOTICE
Short-circuit hazard.

Take the maximum possible ambient temperature into account when selecting the

connecting cables.
The cables must be suitable for operation in a temperature that is 20 K higher than the

maximum ambient temperature.

NOTICE
Device can be irreparably damaged

When performing an insulation test of the entire installation with AC or DC, the device

should be disconnected before starting the test.

Содержание SENTRON PAC3200T









































































































































Результаты поиска

Содержание SENTRON PAC3200T

Отзывы:

Siemens SENTRON PAC3200T, Руководство по эксплуатации продукта, Страница: 34 / 136

Результаты поиска

Содержание SENTRON PAC3200T

Отзывы: