Siemens SCALANCE XR324-4M EEC Скачать руководство пользователя страница 46

Страница: 46 / 84

Signaling contact 100 to 240 VAC / 60 to 250 VDC

The signaling contact is connected to a 3-pin plug-in terminal block.

NOTICE
Damage to the device due to incorrectly wiring the terminal blocks
With devices with a supply voltage of 100 to 240 VAC and 60 to 250 VDC, the terminal blocks

for the power supply and signaling contact are plugged in and screwed down in the device.

Both terminal blocks have three pins but coding prevents the two terminal blocks being

confused.
Make sure that the cables of the power supply and the cables for the signaling contact are

connected to the correct terminal block.

Table 6-2

Pin assignment of the 100 to 240 VAC / 60 to 250 VDC signaling contact

Pin number

Assignment

NC contact

Root

NO contact

To wire up the signaling contact, use a copper cable of category 18-8 AWG or cable with a

cross-section of 0.75 to 6 mm².

NOTICE
Securing cables with dangerous voltage
Make sure that the connector cannot be released accidentally by pulling on the connecting

cable. Lay the cables in cable ducts or cable channels and secure the cables, where

necessary, with cable ties.

Connecting
6.5 Signaling contact

SCALANCE XR-300M EEC

Compact Operating Instructions, 11/2019, A5E02661176-14

Содержание SCALANCE XR324-4M EEC





















































































Результаты поиска

Содержание SCALANCE XR324-4M EEC

Отзывы:

Похожие инструкции для SCALANCE XR324-4M EEC

Бренды по названию

Популярные бренды

Siemens SCALANCE XR324-4M EEC, Краткое руководство по эксплуатации

Результаты поиска

Содержание SCALANCE XR324-4M EEC

Отзывы:

Похожие инструкции для SCALANCE XR324-4M EEC

Бренды по названию

Популярные бренды