Siemens SCALANCE XR324-4M EEC Скачать руководство пользователя страница 52

Страница: 52 / 84

Terminal block assignment (4-pin)

Table 6-4

Pinout of the 24 to 48 V safety extra-low voltage (SELV)

Pin number

Assignment

Pin 1

L1+ (24...48 VDC)

Pin 2

Pin 3

Pin 4

L2+ (24...48 VDC)

To wire up the power connector, use a copper cable of category 18-12 AWG or cable with a

cross-section of 0.75 to 2.5 mm².

6.7.1.4

Connecting a redundant power supply to the XR300-EEC

Device variants with 1 or 2 power supply units

There are devices variants with one power supply unit or with two power supply units. With

device variants with two power supply units, the 2nd power supply unit is also known as the

redundant power supply unit.
The connection is made using a 4-terminal plug-in terminal block to which two power supply

units can be connected (connected redundantly).
If two power supply units are connected, this is known as a redundant power supply.
Connect two power supplies as described below to achieve a correlation between the pin

assignment and LED display.

Connecting a redundant power supply to 1 power supply unit
Use "PS1" to connect the power supply of the terminal block.

PS1

Figure 6-2

Assignment of the LED display to the pins for redundant power supply with devices with one
power supply unit

Connecting
6.7 Power supply

SCALANCE XR-300M EEC

Compact Operating Instructions, 11/2019, A5E02661176-14

Содержание SCALANCE XR324-4M EEC





















































































Результаты поиска

Содержание SCALANCE XR324-4M EEC

Отзывы:

Похожие инструкции для SCALANCE XR324-4M EEC

Бренды по названию

Популярные бренды

Siemens SCALANCE XR324-4M EEC, Краткое руководство по эксплуатации

Результаты поиска

Содержание SCALANCE XR324-4M EEC

Отзывы:

Похожие инструкции для SCALANCE XR324-4M EEC

Бренды по названию

Популярные бренды