Siemens SCALANCE XR324-4M EEC Скачать руководство пользователя страница 32

Страница: 32 / 84

5.4

19" rack mounting

CAUTION

Danger of injury by falling objects
If you do not use the supplied mounting brackets for 19"rack installation, it is not possible to

install the device correctly.
Use only the supplied mounting brackets.
There are several ways of fixing the mounting brackets depending on the mounting position

required.

19" rack mounting

19" rack mounting is possible for all rack devices identified by (XR).

Refer to the technical specifications, Installation options table for each product group. The rack

device is installed using two mounting brackets fitted to the front. After fitting the two mounting

brackets, the rack device can then be installed in a 19" cabinet.

NOTICE
Do not cover the ventilation grilles
During installation, select a mounting position so that the ventilation grilles are always free to

achieve adequate cooling. With normal orientation, the ventilation grilles are on the top,

bottom and sides of the housing.
If you install more than one rack device, make sure that the permitted ambient conditions are

met for all devices in the rack.

Minimum clearances

If you install the IE Switch in rack devices without forced ventilation or cooling, minimum

clearances must be maintained to neighboring devices or the wall of the enclosure. By keeping

to the minimum clearances, there is then an adequate stream of air for heat dissipation during

operation. Keep to the following minimum clearances to neighboring devices.

Table 5-1

Minimum clearances for installation in rack devices

Minimum clearance to devices below the switch

100 mm

Minimum clearance to devices above the switch

100 mm

Minimum clearance between two SCALANCE XR-300 EEC at an am‐

bient temperature up to 70 °C without external ventilation

100 mm

Minimum clearance between two SCALANCE XR-300 EEC at an am‐

bient temperature up to 60 °C without external ventilation

45 mm (1 height unit)

Assembling
5.4 19" rack mounting

SCALANCE XR-300M EEC

Compact Operating Instructions, 11/2019, A5E02661176-14

Содержание SCALANCE XR324-4M EEC





















































































Результаты поиска

Содержание SCALANCE XR324-4M EEC

Отзывы:

Похожие инструкции для SCALANCE XR324-4M EEC

Бренды по названию

Популярные бренды

Siemens SCALANCE XR324-4M EEC, Краткое руководство по эксплуатации

Результаты поиска

Содержание SCALANCE XR324-4M EEC

Отзывы:

Похожие инструкции для SCALANCE XR324-4M EEC

Бренды по названию

Популярные бренды