Siemens Brodersen MC55 Скачать руководство пользователя страница 85

Страница: 85 / 475

MC55_ATC_V04.00

Page 85 of 475

3/17/06

Confidential / Released

Serial Interface Control Commands

The AT Commands described in this chapter allow the external application to determine various settings related

to the MC55's serial interface.

4.1

AT\Q Flow control

Syntax

Parameter Description

[0]

(&F)

Disable flow control

XON/XOFF software flow control

Only CTS by DCE (TA)

RTS/CTS hardware flow control

Recommended for the following procedures: incoming or outgoing data calls,

fax calls, MUX mode.

Often, the initialization routine of Fax programs includes enabling RTS/CTS

handshake, eliminating the need to issue

AT\Q

3 once again.

Notes

• When using XON/XOFF flow control (

AT\Q

1) in online mode,

+++

should not be used while the data trans-

mission is paused with XOFF. Before entering the command mode with

+++

the paused transmission should

be resumed using the XON character.

• For compatibility reasons, the

AT\Q

command can be used in Multiplex mode, though the settings will not

take effect. However, be aware that whenever you use the

AT\Q

write command in Multiplex mode and then

save the current configuration to the user profile with

AT&W

, the changed

AT\Q

setting will become active after

restart.

Exec Command

AT\Q

[

<n>

]

Response(s)

If RTS/CTS flow control is not supported by interface and

<n>

is 2 or 3:

ERROR

Reference(s)

ASC0 ASC1

MUX1

MUX2

MUX3 Charge

Last

SIEMENS

<n>

(num)(&W)(&V)

Содержание Brodersen MC55




























































































































































































































































































































































































































































































Результаты поиска

Содержание Brodersen MC55

Отзывы:

Бренды по названию

Популярные бренды

Siemens Brodersen MC55, Руководство по управлению

Результаты поиска

Содержание Brodersen MC55

Отзывы:

Бренды по названию

Популярные бренды