Siemens Brodersen MC55 Скачать руководство пользователя страница 61

Страница: 61 / 475

MC55_ATC_V04.00

Page 61 of 475

3/17/06

Confidential / Released

Parameter Description

(&F)

Discard "

+CIEV

" and "

^SLCC

" URCs.

Discard "

+CIEV

" and "

^SLCC

" URCs when TA-TE link is reserved, e.g. in

online data mode. Otherwise they are forwarded directly to the TE.

Buffer "

+CIEV

" and "

^SLCC

" URCsin the TA while TA-TE link is reserved, e.g.

in online data mode, and flush them to the TE afterwards. Otherwise they are

forwarded directly to the TE.

Forward "

+CIEV

" and "

^SLCC

" URCs directly to the TE. If MC55 is in online

data mode, URCs are signaled via sending BREAK (100ms) and stored in a

buffer. Once it is back in command mode e.g. after

+++

was entered, all URCs

stored in the buffer will be output.

(&F)

Keypad event reporting is not supported by MC55.

(&F)

Display event reporting is not supported by MC55.

(&F)

Disable indicator event reporting.

Enable indicator event reporting.

(&F)

TA buffer of URCs defined within this command is cleared when

<mode>

1..3

is entered.

Name of indicator; for a list of all supported indicators please refer to

AT+CIND

and

AT^SIND

Value of indicator; for a list of all values for the supported indicators please refer to

AT+CIND

and

AT^SIND

Note

• If the ME operates on different instances (MUX channels 1, 2, 3 or ASC0/ASC1) avoid different settings for

routing and indicating SMS. For example, if messages shall be routed directly to one instance of the TE (set

with

AT+CNMI

AT^SSDA

), it is not possible to activate the presentation of URCs with

AT+CMER

AT+CNMI

on another instance. Any attempt to activate settings that conflict with existing settings on another interface,

will result in CME ERROR, or accordingly CMS ERROR.

<mode>

(num)

<keyp>

(num)

<disp>

(num)

<ind>

(num)

<bfr>

(num)

(str)

(num)

Содержание Brodersen MC55




























































































































































































































































































































































































































































































Результаты поиска

Содержание Brodersen MC55

Отзывы:

Бренды по названию

Популярные бренды

Siemens Brodersen MC55, Руководство по управлению

Результаты поиска

Содержание Brodersen MC55

Отзывы:

Бренды по названию

Популярные бренды