Siemens Brodersen MC55 Скачать руководство пользователя страница 344

Страница: 344 / 475

MC55_ATC_V04.00

Page 344 of 475

3/17/06

Confidential / Released

13.8

AT+CMGW Write Short Messages to Memory

The execute and write commands transmit a short message (either SMS-DELIVER or SMS-SUBMIT) from TE

to memory storage

<mem2>

. Memory location

<index>

of the stored message is returned. Message status will

be set to 'stored unsent' unless otherwise given in parameter

<stat>

After invoking the execute or write command wait for the prompt ">" and then start to write the message. To save

the message simply enter

<CTRL-Z>

. After the prompt a timer will be started to observe the input.

To abort writing use

<ESC>

. Abortion is acknowledged with "OK", though the message will not be saved.

Syntax

Notes

• If writing fails, for example, if a message is too long, the result code depends on the current setting of the

AT^SM20

command:

If the

AT^SM20

=1 (factory default) any failure to send a message is responded with "OK". Users

should be aware, that despite the "OK" response, the message will not be written to the selected SMS stor-

age.

If the

AT^SM20

equals 0 any failure to write a message is responded with "ERROR".

Test Command

AT+CMGW=?

Response(s)

Exec Command

If text mode (see

AT+CMGF

=1):

AT+CMGW

Response(s)

<CR>

Text can be entered.

<CTRL-Z>

<ESC>

+CMGW:

<index>

If writing fails

ERROR

+CMS ERROR

Write Command

If text mode (see

AT+CMGF

=1):

AT+CMGW=

<oa>

<da>

[, [

<tooa>

<toda>

][,

<stat>

]]

<CR>

Text can be entered.

<CTRL-Z>

<ESC>

Response(s)

+CMGW:

<index>

If writing fails see notes below.

Write Command

If PDU mode (see

AT+CMGF

=0):

AT+CMGW=

<stat>

]

<CR>

PDU can be entered.

<CTRL-Z>

<ESC>

Response(s)

+CMGW:

<index>

If writing fails see notes below.

Reference(s)

ASC0 ASC1

MUX1

MUX2

MUX3 Charge

Last

GSM 07.05

Содержание Brodersen MC55




























































































































































































































































































































































































































































































Результаты поиска

Содержание Brodersen MC55

Отзывы:

Бренды по названию

Популярные бренды

Siemens Brodersen MC55, Руководство по управлению

Результаты поиска

Содержание Brodersen MC55

Отзывы:

Бренды по названию

Популярные бренды