Siemens Brodersen MC55 Скачать руководство пользователя страница 379

Страница: 379 / 475

MC55_ATC_V04.00

Page 379 of 475

3/17/06

Confidential / Released

15.3

AT^SSTGI SAT Get Information

Regularly this command is used upon receipt of an URC "

^SSTN

" to request the parameters of the Proactive

Command.

Then the TA is expected to acknowledge the

AT^SSTGI

response with

AT^SSTR

to confirm that the Proactive

Command has been executed.

AT^SSTR

will also provide any user information, e.g. a selected menu item.

The Proactive Command type value specifies to which "

^SSTN

" the command is related.

Syntax

Parameter Description

MC55 Remote-SAT interface states
0

RESET

OFF

IDLE

PAC

WAIT

Related Proactive Command

Test Command

AT^SSTGI=?

Response(s)

^SSTGI:

(list of supported

<state>

s), (list of supported

Read Command

AT^SSTGI?

Response(s)

^SSTGI:

<state>

Write Command

AT^SSTGI=

Response(s)

ERROR

+CME ERROR

Reference(s)

ASC0 ASC1

MUX1

MUX2

MUX3 Charge

Last

SIEMENS

<state>

(num)

(num)

Содержание Brodersen MC55




























































































































































































































































































































































































































































































Результаты поиска

Содержание Brodersen MC55

Отзывы:

Бренды по названию

Популярные бренды

Siemens Brodersen MC55, Руководство по управлению

Результаты поиска

Содержание Brodersen MC55

Отзывы:

Бренды по названию

Популярные бренды