Siemens Brodersen MC55 Скачать руководство пользователя страница 240

Страница: 240 / 475

MC55_ATC_V04.00

Page 240 of 475

3/17/06

Confidential / Released

Syntax

Parameter Description

0 ... 9 specified with

AT^SISS

Internet service state.

Please note, that the state of an Internet service may influence the state of the serial DCD line. For details see

description of value 2 for parameter

<value>

of command

AT&C

Allocated

Service profile resources are allocated, i.e. at least the service type has been

set (parameter

, value "srvType" of

AT^SISS

). The service is

not opened, but ready for configuration.

Connecting

State after opening a service with

AT^SISO

where the connection is being

established.

If connection setup is successful the service proceeds to the state "4" (Up) and

one of the URCs "

^SISW

" and "

^SISR

" may follow. If connection setup is not

successful, the "

^SIS

" URC may appear and the service enters

6 (Down).

In the case of FTP,

=3 means that the command channel is being

established.

If the service profile is configured as Socket listener, then the listener always

stays at

=3 and

=3 (LISTENER), while the

and

of the dynamically assigned service pro-

file may change. See examples in Section

10.5.1

Test Command

AT^SISO=?

Response(s)

Read Command

AT^SISO?

Response(s)

^SISO:

value "srvType" [,

]

[

^SISO:

...]

Write Command

AT^SISO=

Response(s)

ERROR

+CME ERROR:

<err>

ASC0 ASC1

MUX1

MUX2

MUX3 Charge

Last

(num)

(num)

Содержание Brodersen MC55




























































































































































































































































































































































































































































































Результаты поиска

Содержание Brodersen MC55

Отзывы:

Бренды по названию

Популярные бренды

Siemens Brodersen MC55, Руководство по управлению

Результаты поиска

Содержание Brodersen MC55

Отзывы:

Бренды по названию

Популярные бренды