Siemens Brodersen MC55 Скачать руководство пользователя страница 210

Страница: 210 / 475

MC55_ATC_V04.00

Page 210 of 475

3/17/06

Confidential / Released

9.10

AT+CLIR Calling line identification restriction

The

AT+CLIR

command refers to the GSM supplementary service CLIR (Calling Line Identification Restriction).

Syntax

Parameter Description

Parameter shows the settings for outgoing calls:
[0]

(P)

Presentation indicator is used according to the subscription of the CLIR service

CLIR invocation

CLIR suppression

Parameter shows the subscriber CLIR service status in the network:
0

CLIR not provisioned

CLIR provisioned in permanent mode

Unknown (e.g. no network, etc.)

CLIR temporary mode presentation restricted

CLIR temporary mode presentation allowed

Note

• The settings made with

AT+CLIR

=1 or

AT+CLIR

=2 are used for all outgoing calls until the ME is switched off

AT+CLIR

=0 is used.

Test Command

AT+CLIR=?

Response(s)

+CLIR:

(list of supported

<n>

Read Command

AT+CLIR?

Response(s)

+CLIR

<n>

<m>

ERROR

+CME ERROR: <err>

Write Command

AT+CLIR=

[

<n>

]

Response(s)

ERROR

+CME ERROR: <err>

Reference(s)

ASC0 ASC1

MUX1

MUX2

MUX3 Charge

Last

GSM 07.07

<n>

(num)

<m>

(num)

Содержание Brodersen MC55




























































































































































































































































































































































































































































































Результаты поиска

Содержание Brodersen MC55

Отзывы:

Бренды по названию

Популярные бренды

Siemens Brodersen MC55, Руководство по управлению

Результаты поиска

Содержание Brodersen MC55

Отзывы:

Бренды по названию

Популярные бренды