manualshive.com logo in svg

Siemens Brodersen MC55, Руководство по управлению

Поделиться
Скачать
Siemens Brodersen MC55 Скачать руководство пользователя страница 17

MC55_ATC_V04.00

Page 17 of 475

3/17/06

Confidential / Released

 

1.4

AT Command Syntax

The "AT" or "at" prefix must be set at the beginning of each command line. To terminate a command line enter

<CR>

. Commands are usually followed by a response that includes "

<CR><LF>

<response>

<CR><LF>

". Through-

out this document, only the responses are presented, 

<CR><LF>

 are omitted intentionally. 

Table 1.4: 

Types of AT commands and responses 

1.4.1

Using Parameters

• Optional parameters are enclosed in square brackets. If optional parameters are omitted, the current settings

are used until you change them.

• Optional parameters or subparameters can be omitted unless they are followed by other parameters. If you

want to omit a parameter in the middle of a string it must be replaced by a comma. See also example 1.

• A parameter value enclosed in square brackets represents the value that will be used if an optional parameter

is omitted. See also example 2.

• When the parameter is a character string, e.g. 

<text>

 or 

<number>

, the string must be enclosed in quotation

marks, e.g. "Charlie Brown" or "+49030xxxx". Symbols in quotation marks will be recognized as strings. 

• All spaces will be ignored when using strings without quotaton marks.
• It is possible to omit the leading zeros of strings which represent numbers.
• If an optional parameter of a V.250 command is omitted, its value is assumed to be 0.
Example 1: Omitting parameters in the middle of a string 

Example 2: Using default parameter values for optional parameters 

AT command type

Syntax

Function

Test command

AT+CXXX=?

The mobile equipment returns the list of parameters and value 

ranges set with the corresponding Write command or by internal 

processes.

Read command

AT+CXXX?

This command returns the currently set value of the parameter or 

parameters.

Write command

AT+CXXX=<...>

This command sets user-definable parameter values.

Exec(ution) command AT+CXXX

The execution command reads non-variable parameters deter-

mined by internal processes in the GSM engine.

AT+CCUG?

Query current setting

+CCUG: 1,10,1

OK

AT+CCUG=,9

Set only the middle parameter

OK

AT+CCUG?

Query new setting

+CCUG: 1,9,1

OK

AT+CFUN=5

Activate CYCLIC SLEEP mode, don't reset ME

OK

AT+CFUN?

Query ME mode

+CFUN: 5

OK

AT+CFUN=

Set ME back to normal (default parameters: 1,0)

OK

+CFUN: 1

OK

Содержание Brodersen MC55




























































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды