Siemens Brodersen MC55 Скачать руководство пользователя страница 391

Страница: 391 / 475

MC55_ATC_V04.00

Page 391 of 475

3/17/06

Confidential / Released

16.6

AT^SPBD Purge phonebook memory storage

AT^SPBD

can be used to purge the selected phonebook

manually, i.e. all entries stored in the

selected phonebook storage will be deleted. CAUTION! The operation cannot be stopped nor reversed!

The

AT^SPBD

test command returns the list of phonebooks which can be deleted with

AT^SPBD

An automatic purge of the phonebooks is performed when the SIM card is removed and replaced with a different

SIM card. This affects the ME based part of the "LD" storage, and storages "MC" and "RC". Storage "ME" is not

affected.

Syntax

Parameter Description

If test command: List of phonebooks which can be deleted by

AT^SPBD

If write command: Phonebook to be deleted.

For a detailed description of storages see

AT+CPBS

"LD"

Last number dialed phonebook

"MC"

Missed (unanswered received) calls list

"RC"

Received calls list

Note

• Users should be aware that when using this AT command quickly after SIM PIN authentication the SIM data

may not yet be accessible, resulting in a short delay before the requested AT command response is returned.

See Section

20.1

Restricted access to SIM data after SIM PIN authentication

for further detail.

Test Command

AT^SPBD=?

Response(s)

^SPBD:

list of supported

+CME ERROR

Write Command

AT^SPBD=

Response(s)

+CME ERROR

Reference(s)

ASC0 ASC1

MUX1

MUX2

MUX3 Charge

Last

SIEMENS

(str)

Содержание Brodersen MC55




























































































































































































































































































































































































































































































Результаты поиска

Содержание Brodersen MC55

Отзывы:

Бренды по названию

Популярные бренды

Siemens Brodersen MC55, Руководство по управлению

Результаты поиска

Содержание Brodersen MC55

Отзывы:

Бренды по названию

Популярные бренды