Siemens Brodersen MC55 Скачать руководство пользователя страница 164

Страница: 164 / 475

MC55_ATC_V04.00

Page 164 of 475

3/17/06

Confidential / Released

Parameter Description

Status
0

Unknown

Operator available

Current operator

Operator forbidden

Operator
If test command: Operator name in long alphanumeric format and numeric format.

If read command: Operator name as per

If write command: Operator name in numeric format.

Parameter values 0 and 1 are stored non-volatile in the MC55.
0

(D)

Automatic mode;

<oper>

field is ignored.

Manual operator selection

Write command requires

<oper>

in numeric format, i.e.

shall be 2.

Read command returns the current

<mode>

and the currently selected

<oper>

. If no operator is selected,

and

<oper>

are omitted.

Manually deregister from network and remain unregistered until

<mode>

=0 or

1 or 4 is selected.

Set only

(for

AT+COPS

read command).

Automatic / manual selection; if manual selection fails, automatic mode

(

<mode>

=0) is entered (

<oper>

field will be present).

(&F)

Long alphanumeric format of

<oper>

. Can be up to 16 characters long.

Numeric format of

<oper>

. This is the GSM Location Area Identification (LAI)

number, which consists of the 3-digit Mobile Country Code (MCC) plus the 2-

or 3-digit Mobile Network Code (MNC).

Write Command

AT+COPS=

<mode>

<oper>

]]

Response(s)

ERROR

+CME ERROR:

<err>

Reference(s)

ASC0 ASC1

MUX1

MUX2

MUX3 Charge

Last

GSM 07.07

(num)

<oper>

(str)

<mode>

(num)(&V)

(num)(&W)(&V)

Содержание Brodersen MC55




























































































































































































































































































































































































































































































Результаты поиска

Содержание Brodersen MC55

Отзывы:

Бренды по названию

Популярные бренды

Siemens Brodersen MC55, Руководство по управлению

Результаты поиска

Содержание Brodersen MC55

Отзывы:

Бренды по названию

Популярные бренды