manualshive.com logo in svg

Siemens Brodersen MC55, Руководство по управлению

Поделиться
Скачать
Siemens Brodersen MC55 Скачать руководство пользователя страница 409

MC55_ATC_V04.00

Page 409 of 475

3/17/06

Confidential / Released

 

17.9

AT^SNFA Set or query of microphone attenuation 

AT^SNFA

 specifies the large-scale attenuation on the microphone path of the audio device currently selected

with 

AT^SNFS

. The write command is only available in audio modes 2 to 6. 

Syntax

Parameter Description

Multiplication factor for input samples. Parameter 

<atten>

 is identical with 

<inCalibrate>

 of 

AT^SNFI

.

Formula used to calculate microphone attenuation (negative gain):

Gain in dB = 20 * log(

<atten>

/32768)

0...32767

(P)

...65535

0

Microphone is muted. 

Please note that 

AT^SNFA

 cannot be used to mute the microphone. Therefore,

any attempt to enter 0 will be rejected with error response. Value 0 is returned

only by the read command 

AT^SNFA

? after the microphone was muted with

AT^SNFM

=0 during an active call. 

32767

No attenuation on the microphone path

Values greater than 32767 will be suppressed to 32767. 

Notes

• This command is provided for compatibility with former products (e.g. M20) and is a subset of 

AT^SNFI

. The

parameter 

<inCalibrate>

 of 

AT^SNFI

 is identical with 

<atten>

 of 

AT^SNFA

. 

• To make the changes persistent use 

AT^SNFW

. 

Test Command

AT^SNFA=?

Response(s)

^SNFA: 

(list of supported 

<atten>

s) 

OK

Read Command

AT^SNFA?

Response(s)

^SNFA: 

<atten>

OK

Write Command

AT^SNFA=

<atten>

Response(s)

OK

ERROR

CME ERROR: <err>

Reference(s)

PIN

ASC0 ASC1

MUX1

MUX2

MUX3 Charge

Last

SIEMENS

!

%

%

%

%

%

!

!

!

<atten>

(num)(^SNFW)

Содержание Brodersen MC55




























































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды