Siemens Brodersen MC55 Скачать руководство пользователя страница 407

Страница: 407 / 475

MC55_ATC_V04.00

Page 407 of 475

3/17/06

Confidential / Released

17.8

AT^SAIC Audio Interface Configuration

AT^SAIC

configures the interface connections of the active audio mode. The write command is usable in audio

modes 2 to 6 only.

AT^SNFS

=1, any attempt to use

AT^SAIC

write command is rejected with error response. This is because all

default parameters in audio mode 1 are determined for type approval and are not adjustable.

To allocate a specific audio mode to one of the audio interfaces, first select the audio mode with

AT^SNFS

and

then choose the interface using

AT^SAIC

Syntax

Parameter Description

Input and output selection
1

Digital input and output

Analog input and output

Microphone selection
1

Microphone 1

Microphone 2

Select differential earpiece amplifier
1

Selects the earpiece amplifier 1

Selects the earpiece amplifier 2

Selects both amplifiers. Note that both amplifiers are connected in parallel and

therefore, get the same output power if

<ep>

=3.

Test Command

AT^SAIC=?

Response(s)

^SAIC:

(list of supported

<io>

s), (list of supported

<mic>

s), (list of supported

<ep>

Read Command

AT^SAIC?

Response(s)

^SAIC:

<io>

<mic>

<ep>

Write Command

AT^SAIC=

<io>

<mic>

<ep>

]]

Response(s)

ERROR

+CME ERROR: operation not allowed

Reference(s)

ASC0 ASC1

MUX1

MUX2

MUX3 Charge

Last

SIEMENS

<io>

(num)(^SNFW)

<mic>

(num)(^SNFW)

<ep>

(num)(^SNFW)

Содержание Brodersen MC55




























































































































































































































































































































































































































































































Результаты поиска

Содержание Brodersen MC55

Отзывы:

Бренды по названию

Популярные бренды

Siemens Brodersen MC55, Руководство по управлению

Результаты поиска

Содержание Brodersen MC55

Отзывы:

Бренды по названию

Популярные бренды