SICK Bulkscan Скачать руководство пользователя страница 41

Страница: 41 / 112

O P E R AT I N G I N S T R U C T I O N S | Bulkscan®

8014829/ZV98/2018-05-07| S I C K

Subject to change without notice

4 1

MOUNTING

5.3.9

Mounting of Bulkscan® LMS111 with mounting kit 2 or 3

With the aid of mounting kits 2 and 3 (only in conjunction with mounting kit 1a or 1b)

you can align the Bulkscan® LMS111 in two planes. The maximum adjustment angle is

±11° in both planes.

Mounting kit 1a

Mounting kit 2

Mounting kit 3

Threaded holes M4

Centring pin

Fig. 22: Mounting with mounting kit 2 (part no. 2039302) and kit 3 (part no.

2039303)
1. Mount mounting kit 1a or 1b to the Bulkscan® LMS111.
2. Mount the mounting kit 3 on the mounting surface.
3. Fit the centring pin (4 mm) in the central hole on mounting bracket 3.

4. Fit mounting kit 2 to mounting kit 3 and mount it using two fixing screws M4 × 10.

5. Then mount the Bulkscan® LMS111 on mounting kit 2 with the aid of the threaded

holes in mounting kit 1a.
6. Adjust the Bulkscan® LMS111 longitudinally and transversely and then tighten the

six fixing screws on the mounting kits.

During mounting, please observe the dimensional drawings (see "11.4.6 Dimensional

drawing mounting kits (only for Bulkscan® LMS111)“ on page 92).

5.3.10

Mounting of Bulkscan® LM511 with weather protection hood

To protect the Bulkscan® LMS511 from glare, precipitation and direct sunlight when

used outside the weather protection hood (part no. 2063050) is available.

You will find detailed dimensions in section „11.4.7 Dimensional drawing weather pro

tection hood for Bulkscan® LMS511“

Note

Содержание Bulkscan

















































































































Результаты поиска

Содержание Bulkscan

Отзывы:

Похожие инструкции для Bulkscan

Бренды по названию

Популярные бренды

SICK Bulkscan, Руководство по эксплуатации

Результаты поиска

Содержание Bulkscan

Отзывы:

Похожие инструкции для Bulkscan

Бренды по названию

Популярные бренды