SICK Bulkscan Скачать руководство пользователя страница 71

Страница: 71 / 112

O P E R AT I N G I N S T R U C T I O N S | Bulkscan®

8014829/ZV98/2018-05-07| S I C K

Subject to change without notice

7 1

COMMISSIONING

• We recommend setting a value of at least 5 mm to avoid incorrect measurement due

to conveyor belt vibration.

How to configure the ignoring of measurement points below the reference contour:



Switch to the

System

tab.



Activate the

Ignore measurement points below the reference contour

checkbox.



Configure the

Threshold

value in mm.

8.3.5

Contour smoothing (only valid for Bukscan

LMS111)

The contour smoothing function allows to smooth the measured contour in order to

avoid short-term fluctuations on the volume measurement. A high level of contour

smoothing is recommended for rough measurement contours.
Available values for the

Contour smoothin

g function are

Off, Low, Medium, High,

Maximal.
How to configure the smoothing of the measured contour:



Switch to the

System

tab.



Configure the optimal

Contour smoothing

level for your application.

8.4

Monitoring of the contamination degree

The front screen of the Bulkscan® may become contaminated due to the environmen-

tal conditions. This reduces the emitted and received energy from the laser beam and

thereby the measurement accuracy.
The Bulkscan® has six contamination sensors which monitor contamination during

operation.
You can choose from different contamination measurement strategies, these determine

the number of contamination sensors which are evaluated.

Strategy

Behavior

Inactive

Contamination measurement is not carried out

Highly availabe

Contamination warning and contamination errors are only output when

the front screen is uniformly contaminated.

Available

Contamination warning and contamination errors are output when the

front screen is partially contaminated.

Sensitive

Contamination warning and contamination errors are output even when

there is just a little or local contamination.

Tab. 18: Contamination measurement strategies

A contamination warning is output first for the different degrees of contamination. If

the front screen is not cleaned and contamination increases, then a contamination

error is output and the Bulkscan® stops the measuring operation.
Static charges cause dust particles to be attracted to the front screen. The front screen

of the Bulkscan® should be cleaned regularly and in the event of contamination (see

"9.1 Cleaning the front screen“ on page 76).

How to configure contamination measurement:

Note

Содержание Bulkscan

















































































































Результаты поиска

Содержание Bulkscan

Отзывы:

Похожие инструкции для Bulkscan

Бренды по названию

Популярные бренды

SICK Bulkscan, Руководство по эксплуатации

Результаты поиска

Содержание Bulkscan

Отзывы:

Похожие инструкции для Bulkscan

Бренды по названию

Популярные бренды