Sharp MX-2314N, Руководство по обслуживанию

Страница: 139 / 524

MX-3114N SIMULATION 6 – 6
46 42 Used to adjust the FAX send image density. (Fine)
43 Used to adjust the FAX send image density. (Super Fine)
44 Used to adjust the FAX send image density. (Ultra fine)
45 Used to adjust the FAX send image density. (600dpi).
47 Used to set the compression rate of copy and scan images (JPEG).
51 Used to adjust the gamma for the copy mode heavy paper mode and the image process mode.
52 Used to set the gamma default for the copy mode heavy paper and the image process mode.
(After execution of either SIM46-54 or SIM46-51, the adjustment value is reset to the initial value.)
54 Used to perform the engine halftone automatic density adjustment (dither).
58 Used to set the copy mode pseudo resolution. (Smoothing process)
59 Used to perform the copy mode pseudo resolution image process adjustment.
60 Used to adjust the sharpness in the color auto copy mode.
61 Used to adjust the area separation recognition level.
62 Used to set the operating conditions of the ACS, the area separation, the background image process, and
the auto exposure mode.
63 Used to adjust the density in the copy low density section.
65 Used to set the color correction table.
74 Copy color balance adjustment (Auto adjustment)/Printer color balance adjustment (Auto adjustment)
48 1 Used to adjust the scan image magnification ratio (in the main scanning direction and the sub scanning
direction).
5 Used to correction the scan image magnification ratio (in the sub scanning direction). Scanner section
6 Used to adjust the rotation speed of each motor.
49 1 Used to perform the firmware update.
3 Used to update the operation manual in the HDD.
5 Used to perform the watermark update.
50 1 Copy image position, image loss adjustment
5 Used to adjust the print lead edge image position. (PRINTER MODE)
6 Used to adjust the copy image position and the image loss. (RSPF mode) RSPF
10 Used to adjust the black print image magnification ratio and the off-center position.
(The adjustment is made separately for each paper feed section.)
12 Used to perform the scan image off-center position adjustment.
(The adjustment is made separately for each scan mode.)
20 Image registration adjustment (Main scanning direction)
22 Used to adjust the image registration. (Main scan direction, sub scan direction)
(Auto adjustment)/OPC drum phase adjustment (Auto adjustment)
24 Used to display the detail data of SIM 44-2, 50-20 and 22.
27 Used to perform the image loss adjustment of scanned images in the FAX or image send mode.
28 Used to automatically adjust the image loss, void area, image off-center, and image magnification ratio.
51 1 Used to adjust the ON/OFF timing of the secondary transport voltage.
2 Used to adjust the contact pressure (deflection amount) on paper by the main unit and the RSPF resist
roller. (This adjustment is performed when there is a considerable variation in the print image position on
the paper or when paper jams frequently occur.)
53 6 Used to adjust the detection level of the RSPF document width.
7 Used to adjust the RSPF document size width sensor.
8 Used to adjust the document lead edge reference and the RSPF mode document scan position.
9 RSPF dirt detection setting
10 RSPF dirt detection execution
55 1 Used to set the specifications of the engine control operations. (SOFT SW)
2 Used to set the specifications of the scanner control operation. (SOFT SW)
3 Used to set the specifications of the controller operation. (SOFT SW)
10 Used to set the special stamp text. (Taiwan only)
56 1 Used to transport data between HDD - MFP PWB SRAM/EEPROM. (Used to repair the PWB.)
2 Used to backup the data in the EEPROM. SD Card, and HDD (including user authentication data and
address data) to the USB memory. (Corresponding to the device cloning and the storage backup.)
3 Used to backup the document filing data to the USB memory.
4 Used to backup the JOB log data to the USB memory.
5 Used to import the SIM22-6 data to a USB memory in the TEXT format.
6 Used to import the SIM23-2 data into a USB memory in the TEXT format.
7 Used to import SYSLOG data into a USB memory
11 Copy the SD card data to option HDD MFP PWB/HDD
12 Copy option HDD to the SD card MFP PWB/HDD
60 1 Used to check the memory operations (read/write) of the MFP PWB.
61 1 Used to check the LSU polygon motor rotation and laser detection. LSU
3 Used to set the laser power
4 Used to print the print image skew adjustment pattern. (LSU unit)
62 1 Used to format the hard disk/SD Card. (HDD: Excluding the Operation manual and the watermark data)
(SD Card: User data)
2 Used to check read/write of the hard disk (partial).
3 Used to check read/write of the hard disk (all areas).
6 Used to perform the self diagnostics of the hard disk.
7 Used to print the hard disk self diagnostics error log.
Main Sub Functions Section