Servomex SERVOPRO FID Скачать руководство пользователя страница 55

Страница: 55 / 67

SERVOPRO FID Online Total Hydrocarbons Analyser

SERVOPRO FID 01000001A rev:5 53

9 ERROR MANAGEMENT

9.1 System error

This section describes in detail all possible system errors.

Air flow deviation:

This error occurs when the difference between air flow and

air flow set point is higher than 5 cc/min. When this error is active, it is
impossible to ignite the flame.

Low air flow:

This error occurs when the air flow is below 10 cc/min. When this

error is active, it is impossible to ignite the flame.

Fuel flow deviation:

This error occurs when the difference between fuel flow and

fuel flow set point is higher than 5 cc/min. When this error is active, it is
impossible to ignite the flame.

Low fuel flow:

This error occurs when the fuel flow is below 10 cc/min. When

this error is active, it is impossible to ignite the flame.

Sample flow deviation:

This error occurs when the difference between sample

flow and sample flow set point is higher than 5 cc/min. When this error is active,
it is impossible to ignite the flame.

Ambient temperature deviation:

This error occurs when ambient temperature is

out of range. Ambient temperature must be between 5

C and 40

FID temperature deviation:

This error occurs when the difference between

actual F.I.D temperature and FID temperature set point is higher then 10

C. When

this error is active, it is impossible to ignite the flame.

Glow plug damaged:

A glow plug is used to ignite the detector. If the glow plug

is damaged, this error message is displayed. When this error is active, it is
impossible to ignite the flame. The glow plug must be changed.

Flame off:

This error occurs when the FID’s flame is off.

Sample flow reg. problem

: A problem appears with sample pressure regulator,

the system will have to be restarted. If after rebooting, you still have this error,
contact Servomex.

Air flow reg. problem

: A problem appears with air pressure regulator, the system

will have to be restarted. If after rebooting, you still have this error, contact
Servomex.

Содержание SERVOPRO FID




































































Результаты поиска

Содержание SERVOPRO FID

Отзывы:

Бренды по названию

Популярные бренды

Servomex SERVOPRO FID, Руководство оператора

Результаты поиска

Содержание SERVOPRO FID

Отзывы:

Бренды по названию

Популярные бренды