Servomex SERVOPRO FID Скачать руководство пользователя страница 36

Страница: 36 / 67

SERVOPRO FID Online Total Hydrocarbons Analyser

SERVOPRO FID 01000001A rev:5 34

4.8.3 Clock

The clock menu allows configuring the date and time of analyser. This is used to
report error messages.

Figure 23 – Time and date menu

To configure the time, press 1 and then enter hour, minute and second. Between
each value, press E to validate. Do the same for the date.

4.8.4 Log Amp

This menu allows configuring the amplifier board.

Figure 24 - Log amplifier menu

Figure 25

Parameter

Range

Description

Pre-amp

1-1000

First stage gain of the conditioning module

Gain

1-4095

Gain of the conditioning module

Offset

0-10

Offset in volt

Counts

0-16777216

Amplifier signal.

From 0 to 4.9999 the offset is negative and from 5.0001 and 10 the offset is

positive.

<-- <<<HIDDEN 3: Time and Date>>>

1) Time HH:MM:SS 12:59:12
2) Date DD/MM/YYYY 13/01/2009

<-- <<<HIDDEN 4: Log amplifier>>>
1) Preamp: 10 Counts: 3298034
2) Gain: 10.0000
3) Offset: 5.0300

Содержание SERVOPRO FID




































































Результаты поиска

Содержание SERVOPRO FID

Отзывы:

Бренды по названию

Популярные бренды

Servomex SERVOPRO FID, Руководство оператора

Результаты поиска

Содержание SERVOPRO FID

Отзывы:

Бренды по названию

Популярные бренды