manualshive.com logo in svg

Servomex SERVOPRO FID, Руководство оператора

Поделиться
Скачать
Servomex SERVOPRO FID Скачать руководство пользователя страница 50

SERVOPRO FID Online Total Hydrocarbons Analyser 

 

 

                                                                                                                                                  

SERVOPRO FID   01000001A  rev:5                                                                           48               
 

3.

 

Go  into calibration menu. Make sure that span and zero gas values are 
properly entered and that they represent the calibration gases. 

4.

 

Once current reading is stable, press the calibration button: 

a.

 

If you are calibrating the span, press the “re-span” button. 

b.

 

If you are calibrating the zero, press the “re-zero” button. 

 

6.2  Configuring the measurement alarms 

 

This section is only applicable if your SERVOPRO  FID  has the 
alarm option. 

 
Two alarms levels are available: Alarms #1 and Alarm #2. An alarm will occur 
when  the current reading of the analyser goes above the alarm setting.  For 
example, if alarm #1 is set to 10 ppm and reading is 12 ppm, alarm #1 will be 
activated.  Alarm #2 must always be higher than alarm #1. When an alarm is 
activated, a relay contact is opened. When there is no alarm, the relay contact is 
closed. Alarms can be monitored by an external monitoring system (see section 
8). Also, alarms are displayed in the run menu as explained in section 4.3.  
 
To configure the alarm levels, refer to Section 4.4. 

6.3  Configuring milliAmp output alarms 

The 4-20 mA output can also be used to monitor system errors. System errors are 
different from measurement alarms. Three modes are available for the milliamp 
(mA) output. 
 
The first one is  “OFF”. This means that system errors  (see section 9)  will  not 
affect the milliamp output. The second one is “LOW”. This means that the 
milliamp output will go below 4 mA if a system error occurs. The other setting is 
“HIGH”. This means that the milliamp (mA)  output will go above 20 mA if a 
system error occurs. 
 
To configure the 4-20 mA output, refer to section 4.4. 
 
 
 
 
 
 
 
 
 
 
 

Содержание SERVOPRO FID




































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды