4 SBF Reference
RTCMDatum
Number:
4049
"OnChange"
interval: block generated each time a set of transformation
parameters is received
This block reports the source and target datum names as transmitted in RTCM 3.x message
types 1021 or 1022. It also reports the corresponding height and quality indicators.
If a service provider only sends out message types 1021 or 1022, this block is trans-
mitted immediately after reception of MT1021 or MT1022. If message types 1023 or 1024
are also sent out, this block is transmitted after the reception of these messages and the
field is set accordingly.
Parameter
Type Units
Do-Not-Use
Description
Sync1
c1
Block Header, see 4.1.1
Sync2
c1
u2
ID
u2
Length
u2
1
byte
u4
0.001
s
4294967295
Receiver time stamp, see 4.1.3
u2
1
week
65535
SourceCRS
c1[32]
Name of the source Coordinate Reference System, right-padded with
zeros.
TargetCRS
c1[32]
Name of the target Coordinate Reference System, right-padded with ze-
ros.
Datum
u1
See the
Datum
field in the
PosLocal
and
SBF blocks.
Datum is set to 255 if this
SourceCRS/TargetCRS
pair is currently
not used by the receiver.
HeightType
u1
Height Indicator field from MT1021 and MT1022. This field indi-
cates how to interpret the height reported in the
PosLocal
and the
SBF blocks:
0:
Geometrical height
1:
Physical height (height definition in target CRS)
2:
Physical height (height definition in source CRS)
QualityInd
u1
Bit field indicating the maximum approximation error after applying the
transformation:
Bits 0-3: horizontal quality indicator:
0:
Unknown quality
1:
Quality better than 21 mm (from MT1021/1022)
2:
Quality 21 to 50 mm (from MT1021/1022)
3:
Quality 51 to 200 mm (from MT1021/1022)
4:
Quality 201 to 500 mm (from MT1021/1022)
5:
Quality 501 to 2000 mm (from MT1021/1022)
6:
Quality 2001 to 5000 mm (from MT1021/1022)
7:
Quality worse than 5001 mm (from MT1021/1022)
9:
Quality 0 to 10 mm (from MT1023/1024)
10:
Quality 11 to 20 mm (from MT1023/1024)
11:
Quality 21 to 50 mm (from MT1023/1024)
12:
Quality 51 to 100 mm (from MT1023/1024)
13:
Quality 101 to 200 mm (from MT1023/1024)
14:
Quality 201 to 500 mm (from MT1023/1024)
15:
Quality worse than 501 mm (from MT1023/1024)
Bits 4-7: vertical quality indicator, same definition as bits 0-3.
Padding
u1[..]
Padding bytes, see 4.1.5
439
Содержание PolaRx5TR
