manualshive.com logo in svg

Sentryway CurveTrack, Руководство по установке системы

Поделиться
Скачать
Sentryway CurveTrack Скачать руководство пользователя страница 7

VIDEOSURVEILLANCE SYSTEMS

SENTRY

WAY

®

CT V2 001

Page 7 of 70

System Installation Guide

1. Introduction

Sentryway  has designed and built this state-of-the-art Closed Circuit Television (CCTV)  Traveling  Camera 

System using the finest materials and components available. The CurveTrack®  consists of a CCTV camera, with 

pan, tilt, and zoom capability, which moves along a rail on a carriage concealed from view within a transparent, 

mirrored enclosure. The carriage is not tethered to any power or video cables. Because the camera moves on a 

rail, line-of-sight and blind spot issues are eliminated and total coverage can be achieved using fewer cameras.

The CurveTrack® camera provides a continuous, high resolution, real-time, moving video picture while 

remaining hidden. The system can be operated in automatic or manual modes. An on-site system operator can 

easily tilt, pan, zoom, and focus the camera  to monitor specific areas and follow activity.

Of primary importance is the fact that individual CurveTrack® systems can be accessed remotely via the 

internet. This capability enables, for instance, corporate headquarter’s personnel to observe and monitor on-

going operations at multiple facilities in real time. Management can maintain total control over display, pricing, 

and stocking of merchandise while ensuring compliance with all operational directives and procedures.

The instructions presented in this manual are intended for technicians and comprise the recommended 

installation procedures for all components of the CurveTrack® system. Operating instructions for the system 

are contained in a separate User’s Manual available from Sentryway

Quiet, long lasting, trouble – free operation of the CurveTrack® system is dependent upon proper installation of 

all components. It is imperative that installation technicians read and understand this manual thoroughly before 

beginning an installation. Installers must use good judgment when slight deviations from these instructions 

are called for.

Содержание CurveTrack







































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды