manualshive.com logo in svg

Sentryway CurveTrack, Руководство по установке системы

Поделиться
Скачать
Sentryway CurveTrack Скачать руководство пользователя страница 53

VIDEOSURVEILLANCE SYSTEMS

SENTRY

WAY

®

CT V2 001

Page 53 of 70

System Installation Guide

7. Installation of copper conductors

7.1 General

The copper conductors transmit video, power, and control signals between the carriage and the control 

equipment. Figures 7-1 through 7-3 illustrate the recommended method for assembling and installing the 

conductors. Before installation, inspect all copper conductors for kinks or deep scratches, and discard those 

that are damaged. Conductors must be smooth and straight to give optimum transmission. Throughout these 

procedures, handle the copper conductors carefully with gloves.

Assembling the individual lengths of conductors will be made easier if they are temporarily supported below 

the rail sections. Use wire, rope, strips of cloth, etc., to improvise slings for the copper conductors. Suspend the 

conductors in the slings to position them for soldering and insertion in the plastic track as work progresses 

down the length of the system run.

Conductors must be cut square and deburred so that mating ends 

butt together tightly. If pipe cutters are used to cut the conductors, 

they will compress the walls of the copper tubing and the inside 

surface of the conductors will need to be reamed out to permit 

insertion of connectors and end plugs.

NOTE

Содержание CurveTrack







































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды