manualshive.com logo in svg

Sentryway CurveTrack, Руководство по установке системы

Поделиться
Скачать
Sentryway CurveTrack Скачать руководство пользователя страница 5

VIDEOSURVEILLANCE SYSTEMS

SENTRY

WAY

®

CT V2 001

Page 5 of 70

System Installation Guide

Table of Contents

1. INTRODUCTION...............................................................................................................7

1.1 Explanation of Symbols.............................................................................................................................8

1.2  Technical Specifications............................................................................................................................9

1.2.1 Physical Dimensions of the camera carriage..........................................................................................10

1.3 Units of measure.........................................................................................................................................10

1.4 General safety precautions.........................................................................................................................10

1.5  Responsibilities of the Installer.................................................................................................................11

2. IDENTIFICATION OF MAJOR COMPONENTS...............................................................12

2.1 System Components...................................................................................................................................12

2.2 Rail Components........................................................................................................................................14

2.3 Carriage Components................................................................................................................................17

2.4 Power supply assembly (power end cap) Components..............................................................................18

3. SITE EVALUATION AND PLANNING...............................................................................19

3.1 Overview.....................................................................................................................................................23

3.2 Setting Up A Schedule................................................................................................................................21

3.3 Planning Installation of the System Run...................................................................................................21

3.4 Material  Inspection and Inventory............................................................................................................22

3.5 Material  Storage.........................................................................................................................................22

3.6 Recommended Tool List.............................................................................................................................23

4. SUPPORT STRUCTURE INSTALLATION........................................................................24

4.1 General.......................................................................................................................................................24

4.2 Fastening Support Hardware to Bar Joists—Perpendicular.....................................................................24

4.3 Fastening Support Hardware to Bar Joists—Parallel................................................................................25

4.4 Fastening Support Hardware to Steel Beams—Perpendicular.................................................................26

4.5 Fastening Support Hardware to Steel Beams—Parallel............................................................................27

4.6 Fastening Support Hardware to C–Purlin Beams—Perpendicular..........................................................28

4.7 Fastening Support Hardware to C–Purlin Beams—Parallel....................................................................30

4.8 Fastening Support Hardware to Flush Concrete–Parallel and Perpendicular.........................................31

4.9 Fastening Support Hardware to Reinforced Concrete Beams..................................................................33

5. THREADED ROD INSTALLATION..................................................................................34

5.1 General.......................................................................................................................................................34

5.2 Cutting the Threaded Rod.........................................................................................................................34

5.3 Installing Threaded Rod in Channel for Parallel Runs............................................................................36
5.4  Installing Turnbuckles on Threaded Rods...............................................................................................38

6.   RAIL SECTION INSTALLATION.......................................................................................40

6.1 Rail Section Inspection..............................................................................................................................40

6.2 Rail Section Cleaning.................................................................................................................................40

6.3 Rail Section Preparation............................................................................................................................40

Содержание CurveTrack







































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды