manualshive.com logo in svg

Sentryway CurveTrack, Руководство по установке системы

Поделиться
Скачать
Sentryway CurveTrack Скачать руководство пользователя страница 22

VIDEOSURVEILLANCE SYSTEMS

SENTRY

WAY

®

CT V2 001

Page 22 of 70

System Installation Guide

Establish a system height (distance from the floor to the system run) that allows adequate clearance from 

obstructions and maximizes the desired viewing area. The rail must be hung a minimum of 2.5 meters above 

the floor at its lowest point. Verify at least 0.3 meter of clearance, from the top of the rail section down, over 

the entire proposed system run.

NOTE

Local   codes   may   dictate   different specific 

distance requirements . 

Power for the CurveTrack® systems should be controlled by dedicated circuit breakers. There should be no 

more than four CurveTrack® Power Supplies (i.e. four system runs) per circuit breaker.

Ensure that floor level obstructions to lift equipment, ladders, etc. are 

accounted for and can be worked around to maintain a safe environment for 

installation workers and bystanders. Be especially aware of the potential hazard 

of falling materials, tools and debris as well as potential trip hazards, including 

power cords, in areas below the installation zone.

DANGER

All CurveTrack® equipment and installation materials that are at the site of the installation must be inspected 

for damage. All Claims for losses, or damage to the system in transit, must be made with the carrier. Packing slip 

documentation should be checked carefully against material received to ensure that everything that is needed 

has arrived. It is suggested that before the actual construction begins, the installation team do a complete 

inventory while the lead installer reviews the site. Any shortages in parts or materials must be reported as soon 

as possible so that corrections can be made in a timely fashion.

After inspection, return all materials to their shipping containers to protect them until they are used. Designate 

a specific storage area in a protected place to prevent accidental damage, especially to delicate electronic parts 

and the easily – damaged windows.

3.4 Material inspection and inventory

3.5 Material storage

Содержание CurveTrack







































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды