manualshive.com logo in svg

Sentryway CurveTrack, Руководство по установке системы

Поделиться
Скачать
Sentryway CurveTrack Скачать руководство пользователя страница 19

VIDEOSURVEILLANCE SYSTEMS

SENTRY

WAY

®

CT V2 001

Page 19 of 70

System Installation Guide

3. Site evaluation and planning

3.1 Overview

A good installation is always preceded by good preliminary planning. A comprehensive site survey and a set 

of floor plans are valuable assets for system planning. It is essential to determine the location best suited for 

the system run(s), and to identify the type of ceiling or roof structure from which it will be suspended, prior to 

specifying the required mounting materials. Proper planning will ensure that you have an adequate supply of 

mounting materials on hand, before starting the installation, to minimize delays.

A system run can be installed either in parallel with, or perpendicular to, bar joists, steel beams, preformed 

concrete beams, or C– Purlin beams. A flat corrugated 

steel roof is yet another possibility which will require its 

own alternative method of installation.

The instructions in Sections 3 and 4 detail specific 

installation methods suitable for the majority of roof and 

ceiling types.

Figure 3-1 illustrates a typical steel beam type of roof 

support structure. Since spacing between beams and 

the distance between the beams and the floor can vary 

greatly, close attention to these variables is important 

when planning for sufficient mounting material.  Read the 

following installation instructions first before deciding 

on the best mounting method and materials to use.

Figure 3-2 illustrates a typical bar joist type of roof 

support structure. Mounting to this type of support will 

not require drilling into the bar joist

Содержание CurveTrack







































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды