User Manual
88
User Manual
89
10-4 Table of Parameter Settings for operator
Customer Name
Model
Telephone
Operational
environment
Address
Parameter Code
Settings
Parameter Code
Settings
Keyboard tap installation hole size : E=74.5mm wide ; F=126mm long.
Product Code
FD300-3-150-C-CE
FD300-3-200-C-CE
FD300-3-300-C-CE
FD300-3-400-C-CE
FD300-3-500-C-CE
Mounting Dimension
Dimension
Pore
Diameter
A (mm)
B (mm)
H (mm)
W (mm)
D (mm)
(mm)
205
180
432
244
518
300
260
497
305
320
220
416
255
234.5
205
f
5.5
f
7
f
9
FD300-3-250-C-CE
FD300-3-600-C-CE
FD300-3-750-C-CE
FD300-3-1000-C-CE
300
620
390
300
598
f
11
FD300-3-075-C-CE
FD300-3-100-C-CE
148
235
247
160
190
f
5.5
B
W
A
For FD300 Series:
D
H
FD300-3-020-C-CE
FD300-3-030-C-CE
FD300-3-050-C-CE
107
f
4.5
175
185
118
167
187
f
4.5
107
175
185
118
PRG
FUNC
ESC
JOG
REV
STOP
RESET
RUN
Hz
V
A
RPM
%
L/R
F/R
RUN
-
+
Please set P3-11 “over-excitation gain” value to “0”. If it is not “0”, it may
cause excessive current during operation. Please set P3-23 “Overvoltage
stall enable” value to “0”. If it is not “0”, it may cause deceleration time to
lengthen the problem.
Please note when using a braking resistor or installing a brake unit or
using an energy feedback unit.
Slip compensation
time constant
0.1~10.0s
Default
:
0.5
P3-27
The smaller the response time value of the slip compensation is set, the
faster the response speed is.
P4: Input terminal
The inverter comes standard with 6 multi-function digital input terminals
(X6 can be used as high-speed pulse input terminal), 2 analog input
terminals.
X1 terminal function selection
X2 terminal function selection
X3 terminal function selection
X4 terminal function selection
X6 terminal function selection
X5 terminal function selection
X7 terminal function selection
X8 terminal function selection
X9 terminal function selection
P4-00
P4-01
P4-02
P4-03
P4-04
P4-05
P4-06
P4-07
P4-08
These parameters are used to set the function of the digital multi-function
input terminal. The functions that can be selected are shown in the table
below.
Setting
value
Function
Instruction
0
No function
The unused terminals can be set to “No function” to
prevent malfunction.
1
Forward RUN
(FWD)
The inverter is controlled to rotate forward and
reverse by external terminals.
2
Reverse RUN
(REV)
3
Three-wire
control
Through this terminal as a three-wire control,
see P4-11 for details.
4
Forward JOG
5
Reverse JOG
6
Terminal UP
The frequency is incremented or decremented when
the frequency is given by the external terminal.
When the frequency source is set to digital setting,
the set frequency can be adjusted up and down.
7
Terminal DOWN
Control the forward and reverse jog operation of the
inverter through external terminals.
Jog running frequency, jog acceleration/deceleration
time see P8-00~P8-02.
P3-34
0
：
Shut off water supply mode The P3-35 ~ P3-40 function is invalid in this
mode.
1
：
Turn on water supply mode After this mode is turned on, PA-00, PA-01,
P8-49 ~ P8-52 functions are invalid, and corresponding functions are
replaced by P3-35 ~ P3-40.
Water supply mode
selection
0: Turn off water supply mode
1: Turn on the water supply mode
Remote transmission
of pressure gauge range
0.00
〜
5.00MPa
Default
:
1.00 MPa
Demand target pressure
0.00
〜
P3-39
Default
:
0.5 MPa
Dormancy frequency
0.00 Hz
〜
P0-10
Default
:
25.00Hz
Sleep latency
0.0
〜
3600.0s
Default
:
0.0s
Wake up the pressure
0.0
〜
100.0%
Default
:
80%
Wake up time delay
0.0
〜
3600.0s
Default
:
0.0s
Default
:
0
P3-35
P3-36
Set P3-35 according to the actual range of the remote transmission
pressure gauge, and then set the desired target pressure value.
P3-37
P3-38
When the feedback pressure is greater than the target pressure, and the
operating frequency continues to be less than the sleeping frequency of P3-
37, it enters the sleeping state after the sleeping delay of P3-38.
P3-39
P3-40
When feedback pressure is less than wake up pressure, After the sleep
delay of P3-40 wake up the converter again.
Default: 1 Forward RUN (FWD)
Default: 4 Forward JOG
Default: 9 Fault reset (RESET)
Default: 12 Multi-speed terminal 1
Default: 13 Multi-speed terminal 2
Default: 0 (no-function)
Default: 0 (no-function)
Default: 0 (no-function)
Default: 0 (no-function)
Chapter 6
Chapter 6
