sauter equitherm EQJW245, Руководство по эксплуатации

Страница: 25 / 127

EQJW245
25/127 www.sauter-controls.com
Commissioning
Parameter Description Range
Step
value
SP07 0
Infl uence of binary / pulse input (terminal 21, 22)
0 = No infl uence on HK1
1 = HK1 in back-up mode if contact closed
2 = HK1 in reduced mode if contact closed
3 = HK1 in nominal mode if contact closed
4 = Pulse input for quantity metering
5 = Seepage limitation
6 = Input for fault signal
0 to 6 1
SP08 0
Room sensor HK1 and 2nd fl ow sensor BW
0 = No room temperature recording
1 = Room sensor NI1000
2 = EGS52/15 or EGT333 with room sensor
3 = EGS52/15 or EGT333 without room sensor
4 = 2nd fl ow sensor for domestic water
0 to 4 1
SP09 0
Room temperature input for HK1
0 = not active
1 = active if T
Ri
> T
Rs
2 = active if T
Ri
< T
Rs
3 = active if T
Ri
<> T
Rs
0 to 3 1
SP10 20 Room temperature input scanning time HK1/[min] 1 to 100 1
SP11 0 Correct room temperature of HK! In K -6.0 to +6.0 0.1
SP12 0 Outside temperature correction in K -10.0 to +10.0 1
SP13 0
Return temperature recording T
RF1
0 = Return temperature not being recorded
1 = T
RF
is recorded up to max. return temperature limit
2 = T
RF
for maintaining return temperature
0 to 2 1
SP14 0 T
RF1
correction in K -10.0 to +10.0 1
SP15 40 Proportional band PI – actuator 1 control in K 2 to 1000 1
SP16 240 Reset time PI – actuator 1 control in seconds 5 to 1000 1
SP17 120 Actuator 1 run-time in seconds 30 to 960 15
SP18 5 Minimum T
F
limit for heating 1 in °C 5 to 100 1
SP19 75 Maximum T
F
limit for heating 1 in °C 20 to 150 1
SP20 90 Upper limit (min. or max.) of T
RF
for HK1, 2 in °C 0 to 150 1
SP21 90 Lower limit (min. or max.) of T
RF
for HK1, 2 in °C 0 to 150 1
SP22 0
TA at which scheduled part of limiting function of T
RF
for HK1, 2 used
in °C
-49 to +49 1
SP23 1.0 Slope of limiting function of T
RF
for HK1, 2 in K/K 0 to 5 0.1
SP24 90 Return temperature limit during domestic water charging in °C 5 to 150 1
SP25 5
Intervention level in control of fi nal control element 1 if limit for T
RF1
[K/K] exceeded
0.1 to 10 0.1
SP26 no
Limit in pulses/min for max. fl ow rate and output
if at least one heating circuit and domestic water preparation is
active
no, 0.1 to 16;
60to 16000
0.1/1/10
SP27 no
Limit in pulses/min for max. fl ow rate and output if at least one hea-
ting circuit but not domestic water preparation is active no, 0.1 to 16;
60 to 16000
0.1/1/10
SP28 no
Limit in pulses/min for max. fl ow rate and output if only domestic
water preparation is active, but none of the heating circuits no, 0.1 to 16;
60 to 16000
0.1/1/10
SP29 0.0 Intervention level on T
F1
in K/min if fl ow rate/output limit exceeded 0.0 to 30.0 0.1
SP30 no Limit in pulses/min for min. fl ow rate and output
no, 0.1 to 16;
60 to 16000
0.1/1/10
SP31 1
Domestic water functions
0 = no domestic water preparation
1 = BW preparation with 1 sensor
2 = BW preparation with 2 sensors
3 = BW preparation using fl ow control
0 to 3 1