Samsung DMT400 series Скачать руководство пользователя страница 40

Страница: 40 / 58

4. Troubleshooting

4-7

Error Type

Error

mode

Checking Method

Corrective actions

Water supply Error

[Or]

‘Smart

Auto’

LED

1. Check whether the water faucet is open.

- Open the faucet.

2. Check whether the water supply has been cut off.

- Close the faucet and turn off the power. Wait until the water supply

resumes.

3. Check whether any foreign material is in the Water Supply Line and the

water Inlet Valve

lter.

- Remove the foreign material. Clean the

lter with a brush.

4. Check the connection for the Inlet Valve connector.

- Reconnect the Inlet Valve connector.

5. Check whether the coil in Inlet Valve is conductive (Remove the connector

before measuring.)

Normal: Approx. 1.2 k

- Faulty: Replace the Inlet Valve.

6. Check whether the Inlet Valve is operating normally.
- Check the operation of the Inlet Valve

Normal: 120V

- Check the Inlet Valve Relay.

: Check the voltage between the yellow wire of the Main PBA CN101
connector and the brown wire of the CN202
Normal: 120V (while operating)

- Faulty: Replace the Main PBA assy.
- Normal: Replace the Inlet Valve

- Remove

Retainer.

- Check

voltage

7. Check whether the water supply stops after water is supplied for 5 seconds.

- Replace the Assy Case Brake which is including Flow Meter.

8. Check whether the water supply stops after water is supplied for 1~5

minutes.

- Check the water supply valve and increase the water pressure.

9. Check whether the water supply stops after water is supplied fully until the

oater in Assy Case sensor is located in High level sensor.

- Replace the Assy Case Sensor which is including water (high &

low) level sensor.

Содержание DMT400 series



























































Результаты поиска

Содержание DMT400 series

Отзывы:

Похожие инструкции для DMT400 series

Бренды по названию

Популярные бренды

Samsung DMT400 series, Руководство по обслуживанию

Результаты поиска

Содержание DMT400 series

Отзывы:

Похожие инструкции для DMT400 series

Бренды по названию

Популярные бренды