Samsung DMT400 series Скачать руководство пользователя страница 44

Страница: 44 / 58

4. Troubleshooting

4-11

Error type

Error mode

Checking Method

Corrective actions

High Temperature
Heating Error

[Or]

‘Normal’ +

‘Smart Auto’

LED

1. Check the hot water connections for the Inlet Valve.. - See the “Temperature Sensor Error”.

2. Check the operation of the Thermistor.

- See the “Heater Error”.

Leakage Error

[Or]

‘Heavy’ LED

Check whether there is any trace of water leakage

in the shutter.

Normal: No water leakage trace

- Faulty: Check the leakage location. Replace the faulty part.
- Normal: Replace the Main PBA assy.

Over-level water error

[Or]

‘Heavy’ +

‘Smart Auto’

LED

1. Check the connections for the Over

ow Sensor

connector.

- Reconnect the Over

ow Sensor connector.

2. Check whether the Inlet Valve operates normally.

- See “Water supply Error”.

3. Check whether water is supplied (even small

amounts) in the intervals when the Inlet Valve is not
operating.

- Remove foreign material from the Inlet Valve.
- If you cannot remove the foreign material from the Inlet Valve, replace it.

4. Check whether there is any trace of water leakage

on the top of the Case Sensor.

- Clean the Hose-Sensor and the Case Sensor.

5. Check whether an “Over Level Water Error” is

detected when the assy wire-harness connector for
Over

ow Sensor is not connected.

Normal: The “Over Level Water Error” does not

occur.

- Faulty: Replace the Main PBA assy
- Normal: Replace the Assy case brake(

ow-meter).

Содержание DMT400 series



























































Результаты поиска

Содержание DMT400 series

Отзывы:

Похожие инструкции для DMT400 series

Бренды по названию

Популярные бренды

Samsung DMT400 series, Руководство по обслуживанию

Результаты поиска

Содержание DMT400 series

Отзывы:

Похожие инструкции для DMT400 series

Бренды по названию

Популярные бренды