Samsung DMT400 series Скачать руководство пользователя страница 41 | Manualshive

Страница: 41 / 58

background image

4. Troubleshooting

4-8

Error type

Error mode

Checking Method

Corrective actions

High temperature Water
supply error

3E

[Or]

‘Normal’ +

‘Delicate’ +

‘Smart Auto’

LED

1. Check the hot water connections for the Inlet Valve.

- Adjust the hot water supply so that the temperate of the supplied water is

less than 176

˚

F (80

˚

C)

2. Check the operation of the Thermistor.

- See the “Temperature sensor error”..

Drain error

5E

[Or]

‘Delicate’ LED

1. Check whether there is any foreign material in the

Drain Hose.

- Remove the foreign material from the Drain Hose.

2. Check the operation of the Water-level sensor

- See the “Low-level water error”

3. Check the connections for the Drain Pump

connector.

- Reconnect the Drain Pump connector.

4. Check whether the Drain Pump coil is conductive.
(Remove the connector before measuring.)

Normal: Approx. 25

Ω

¯

- Faulty: Replace the Drain Pump.

5. Check the operation of the Drain Pump Relay
: Check the operating voltage between the yellow

wire of the Main PBA CN101 connector and the
orange wire of the CN202 connector.

Normal: 120V (while operating)

¯

- Faulty: Replace the Main PBA assy.
- Normal: Replace the Drain Pump.
- Remove retainer.
- Check voltage.

«
...
39
40
41
42
43
...
»

Содержание DMT400 series



























































Отзывы:

Нет отзывов

Похожие инструкции для DMT400 series

Бренд: Favor.it Страницы: 9

Бренд: Daewoo Страницы: 33

Бренд: Roper Страницы: 36

Бренд: Fagor Страницы: 2

Бренд: Dawlance Страницы: 4

Бренд: Hotpoint Страницы: 20

Бренд: Morris Страницы: 25

Бренд: NEFF Страницы: 60

Бренд: Samsung Страницы: 200

Бренд: inventum Страницы: 100

Бренд: Beko Страницы: 20

Бренд: Beko Страницы: 40

Бренд: Beko Страницы: 41

Бренд: Beko Страницы: 20

Бренд: Beko Страницы: 20

Бренд: Beko Страницы: 37

Бренд: Beko Страницы: 45

Бренд: Beko Страницы: 45

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды