Samsung DMT400 series Скачать руководство пользователя страница 38 | Manualshive

Страница: 38 / 58

background image

4. Troubleshooting

4-5

4-2. Service Inspection Mode

4-2-2. DMT400 series

- Press the ‘Heavy’ + ‘Delicate’ + ‘Power’ buttons at the same time for two seconds to enter Service Inspection Mode.
- All LEDs are displayed for the

fi

rst two seconds and then Software-Ver. will be indicated Binary Code using LED of ‘Normal, Heavy, Delicate, Smart Auto’.

-  You can change the mode by pressing the Normal button again. If press the Normal button in this mode, the mode will be changed to next mode.
-  If you want to activate a mode while operating the dishwasher, the door must be closed.
-  If ‘Heavy’ LED , ‘Heavy+Smart Auto’ LED, ‘Heavy+DSmart Auto’ LED error occur, enter Service Inspection Mode after resolving it.
-  Service Inspection Mode is described in the following table.

Mode

Display

Related Parts

Symptoms

Note

No.1

‘Smart Auto’

LED

Drain pump
Inlet Valve
Flow Meter
Water-level sensor
Turbidity

Door open warning

Water supply Error
Low level water Error
Turbidity Error

If Door is open, Door open warning (‘De Smart Auto’ LED) will blink.
If low level sensor is not detected, Drain is executed. Water supply will be executed when low level sensor
is Off.
If water is not fully supplied(sensing on

fl

ow-meter), the Water Supply Error (‘Smart Auto’ LED) will blink.

When high level sensor is not detected after water supply was done, Low-level water error (‘
Heavy + Smart auto’ LED) will blink.
When Turbidity problem is occurred after water supply was done, Turbidity Error (‘ Heavy’ LED)
will blink.
If all functions in this mode are completed, Wash LED will blink.

No.2 ‘Delicate’ LED Circulation Motor

A nozzle does not inject
water.

If Low Level sensor is detected before Circulation Motor is operating, (‘De Sanitize’ LED) will blink.
When water is

fi

lled enough, Circulation Motor -2(190W) will be operated.

No.3

‘Delicate’ +

‘Smart Auto’

LED

Circulation Motor

A nozzle does not inject
water.

If Low Level sensor is detected before Circulation Motor is operating, (‘De Smart auto + Sanitize’
LED) will blink. When water is

fi

lled enough, Circulation Motor- 1(150W) will be operated.

No.4

‘Heavy’ LED

Circulation Motor
Heater
Thermistor
Dispenser

Heater Error

If Low Level sensor is detected before Circulation Motor is operating, (‘Heavy + Sanitize’ LED) will blink.
When water is

fi

lled enough, Circulation Motor 1(150W) and Heater will be operated.

When the temperature meet 60

˚

C or above, the heater is turned off and the ‘Wash’ LED will blink.

If Heater or Thermistor have problems, the Heater Error (‘Heavy + Delicate’ LED) will blink.
Dispenser will operate during 130 seconds only one time.

No.5

‘Heavy’ +

‘Delicate’ +

‘Smart Auto’

LED

Dry Fan Motor
Dispensor

The Dry Fan motor does
not work.

Operate the Dry Fan Motor and check whether Rinse aid is

fi

lled or not.

If there is not rinse aid in Dispenser, Rinse Re

fi

ll lamp is ON.

No.6

‘Normal’ LED

Inlet valve
Over

fl

ow Sensor

Over level water Error

Water is supplied until Over-level water error (‘Heavy + Smart Auto’ LED) is blinked.
If Over-level water error occurs, over

fl

ow sensor is OK.

«
...
36
37
38
39
40
...
»

Содержание DMT400 series



























































Отзывы:

Нет отзывов

Похожие инструкции для DMT400 series

Бренд: lamber Страницы: 70

Бренд: Lamona Страницы: 12

Бренд: Zanussi Страницы: 8

Бренд: Zanussi Страницы: 30

Бренд: ZANKER Страницы: 22

Бренд: Panasonic Страницы: 2

Бренд: Indesit Страницы: 72

Бренд: Glen Dimplex Страницы: 48

Бренд: JUNO Страницы: 10

Бренд: ZANKER Страницы: 4

Бренд: Hotpoint Страницы: 20

Бренд: GE Страницы: 72

Бренд: Baumatic Страницы: 40

Бренд: Furrion Страницы: 26

Бренд: Ariston Страницы: 60

Бренд: montpellier Страницы: 24

Бренд: NEFF Страницы: 56

Бренд: NEFF Страницы: 60

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды