Samsung DMT400 series Скачать руководство пользователя страница 4

Страница: 4 / 58

1-3

1. Safety Instructions

Caution

Before Servicing

Do not sprinkle water onto the dishwasher directly when cleaning it.

ࣃ

This may result in electric shock or

re, and may shorten the product lifetime.

Do not place any containers with water on the dishwasher.

ࣃ

If the water is spilled, it may result in electric shock or

re. This will also shorten the

product lifetime.

Do not install the dishwasher in a location exposed to snow or rain.

ࣃ

This may result in electric shock or

re, and shorten the product lifetime.

Do not press a control button using a sharp tool or object.

ࣃ

This may result in electric shock or damage to the product.

During Servicing

When wiring a harness, make sure to seal it completely so no liquid can enter.

ࣃ

Make sure that they do not break when force is exerted.

Check if there is any residue that shows that liquid entered the electric parts or

ࣃ

harnesses.

If any liquid has entered into a part, replace it or completely remove any remaining

moisture from it.

If you need to place the dishwasher on its back for servicing purposes, place a support(s)

ࣃ

on the

oor and lay it down carefully so the back is on the

oor.

Do not lay it down on its front or side. This may result in scratches to the surface or

damage to the parts.

Содержание DMT400 series



























































Результаты поиска

Содержание DMT400 series

Отзывы:

Похожие инструкции для DMT400 series

Бренды по названию

Популярные бренды

Samsung DMT400 series, Руководство по обслуживанию

Результаты поиска

Содержание DMT400 series

Отзывы:

Похожие инструкции для DMT400 series

Бренды по названию

Популярные бренды